Introduction
The XSC series vortex wet dust collector is an advanced and ideal dust removal equipment that is highly effective in workplace dust collection and has a high dust removal efficiency. It requires minimal water consumption and no additional consumables, resulting in low operating costs and convenient operation.
Working principle of XSC series vortex wet dust collector
The XSC vortex wet dust collector consists of five major systems: dust collection, air supply, dust removal, slag discharge, and control. The dust removal system is the core of the entire system. When the dusty gas enters the dust collector, the gas collides with the water surface at a high velocity and flows through two "S"-shaped channels, causing the water flow to produce a vortex. The particles come into full contact with the water droplets, and through the effects of collision, interception, and condensation, the particles settle with the droplets. At the same time, a large amount of water mist is generated, which is separated from the dust by a water and gas separator. The clean gas is then sent to the chimney for emission compliance through an induced draft fan.
Technical Features:
1.High dust removal efficiency and strong applicability. The unique vortex structure of the vortex wet dust collector gives it a higher dust removal efficiency than ordinary wet dust collectors such as water baths or spray systems. It can also handle high dust concentrations and harsh working conditions. The vortex wet dust collector has a very high dust removal efficiency and good applicability for purifying dust-laden gases with high humidity, high temperature, and acidity or alkalinity.
2. Dust removal and purification combined. The vortex wet dust collector not only removes dust particles from the gas but also removes water vapor and certain water-soluble toxic and harmful gas pollutants from the gas. Therefore, the vortex wet dust collector not only removes dust but also has a cooling and purifying effect on the gas.
3. After the dust removal system is in operation, routine maintenance mainly involves cleaning the dust collection pipes every 3-6 months based on specific working conditions.
XSC series vortex wet dust collector main technical parameters
|
Model |
Rated air volume(m3/h) |
Applicable Range(m3/h) |
Pressure loss(Pa) |
Water Consumption(m3/h) |
Dust Removal Efficiency (％) |
Motor Power(kw) |
|
XSC10 |
10000 |
9047-12063 |
1000-1600 |
1.2 |
＞95 |
30 |
|
XSC20 |
20000 |
18778-25038 |
1000-1600 |
1.3 |
＞95 |
37 |
|
XSC30 |
30000 |
22530-34775 |
1000-1600 |
1.4 |
＞95 |
55 |
|
XSC40 |
40000 |
34300-45700 |
1000-1600 |
1.5 |
＞95 |
55 |
|
XSC50 |
50000 |
45700-57100 |
1000-1600 |
1.5 |
＞95 |
75 |
|
XSC60 |
60000 |
59300-66700 |
1000-1600 |
1.6 |
＞95 |
90 |
|
XSC70 |
70000 |
70200-81400 |
1200-1800 |
1.7 |
＞95 |
110 |
|
XSC80 |
80000 |
69900-84200 |
1200-1800 |
1.8 |
＞95 |
132 |
|
XSC90 |
90000 |
94600-111000 |
1200-1800 |
2 |
＞95 |
160 |
XSC series vortex wet dust collector application
The XSC series vortex wet dust collector is suitable for the removal of trace non-fibrous or non-corrosive dust and gas with a temperature of less than 300℃. It is widely used in metallurgy, coal, chemical, foundry, power generation, building materials, and refractory materials industries. It also has a good effect on the transportation of sticky lime.
Hot Tags: vortex wet dust collector, China vortex wet dust collector manufacturers, suppliers, factory, Deep Wet Electrostatic Precipitator, Vortex Wet Dust Collector, high temperature dust remover such as porous ceramic membranes, Bag Filter Accessories, Vortex Dust Collector, ridgid vacuum bag